Yadda za a Gina Gigon Hanya na Yanke don Ƙungiyar Band

01 na 10

Gabatarwar

Yawancin ayyuka na aikin itace, irin su shimfiɗaɗɗai masu tasowa ko hanyoyi, suna kira don ƙayyadaddun abubuwa, irin waɗanda ba za a iya yanke su ba tare da ido tare da wani ɓangare na igiya ko jigsaw . Don yanke siffofi masu mahimmanci suna buƙatar jig. A cikin wannan koyo, muna tafiya akan mataki zuwa mataki ta hanyar ginawa da yin amfani da jigon yankewa don ganin band din. Yayin da jigs masu linzamin na'ura zasu iya amfani da wannan tsari, band yana ganin jigs masu launi kamar wannan zai iya zama sauki don amfani.

Dalilin aikin shi ne gina a kan matakan plywood da yawa da za su huta a kan tebur na tauraron ka. Zuwa cikin tebur na plywood, za ku haɗa nau'in pivot, wanda ya kasance tsakiyar cibiyar a kan duk abin da kuke so a yanke akan ƙungiyar ku. Ta matsayi pivot fil a wurare daban-daban, za ka iya yanke shingen madauri tare da kowane radius da kake so.

Matsalar Difficulty

• Mai sauƙin matsakaici

Lokaci don kammala

• 30 zuwa 60 minutes

Kayan da Kayi Bukatar

• Band ya ga
• Ƙarfin wutar
• Rahoton yawo
• Matsala Tape
• Fensir
• Yanayin haske

Abubuwan Da ake Bukata

• 2 x 4 ft na 1/2 inch ko 3/4 inch plywood
• 2 x 4, 8 ft. Tsawon (1)
• 1 x 2, 4 ft. Tsawon (1)
• Amfani masu amfani (zaɓi) (2)
• Babban spring clamps (2)
• 4d gama kusoshi

02 na 10

Yanke Plywood

1. Don fara wannan aikin aiki na itace, auna ma'auni na ƙungiyar ku ga teburin (a layi daya da ruwa).
2. Ta amfani da madogarar sautin ko gabar teburin , toshe plywood zuwa nisa kusa da inci uku fiye da wannan nisa. Wannan zai samar maka da 4-ft. Jigon jigon da yake dan kadan fiye da yadda band din ya ga tebur.
3. Kusa gaba, auna ma'aunin tsaka-tsalle daga ɓangaren ɓangaren ku na ɓangaren gefen teburin. Alamar wannan nisa a kan plywood, auna daga gefen daya.
4. Yanke tsawon tsawon 1 x 2 da nisa na plywood, da kuma haɗa shi a alamar tare da sutura na itace . Wannan wata mahimmanci ce da za ta ba ka izini ka haɗa jig zuwa ga ƙungiyarka ga tebur.

03 na 10

Haɗa Al'ummar Wuta

1. Bayan da aka rusa plywood kuma an rufe shi, sai mataki na gaba shi ne hašawa matakai biyu da za a yi amfani da su don ɗaure jig din zuwa ga band.
2. Yanke sassan guda biyu na 1 x 2 kuma sanya daya a kowane gefe na kasa na plywood tsakanin babban mahimmanci (wanda aka haɗe a mataki na baya) da kuma ƙarshen plywood kusa da karamar. Wadannan sanannun zasu taimaka wajen tabbatar da jig din lokacin da aka yi amfani dasu.

04 na 10

Yanke Gwanayen

Yanzu da cewa an haɗa su da magunguna, mataki na gaba shi ne hašawa kafafu biyu.

1. Sanya nesa daga ƙungiyar ku ga teburin zuwa bene. Kashe 3/4 inch daga wannan nisa, kuma yanke sassa biyu na 2 x 4 zuwa wannan ƙimar
2. Yanke sashe na 1 x 2 da nisa na plywood, kuma hašawa wannan sashi zuwa kasan sassan biyu na 2 x 4, kamar yadda aka nuna a hoto. Wannan zai zama matashin kafa don taimakawa wajen kafa kafafu.

05 na 10

Haɗa kafafu

Tare da kammala taron da aka kammala, za mu haɗu da kafafu zuwa ga tebur. A cikin wannan mataki kana da zaɓi biyu, zaka iya haɗa kafafu tare da hinges wanda zai ba da damar kafafu a karkashin teburin lokacin da aka adana shi, ko kuma kawai zaka iya fitar da wasu sutura ta cikin tebur cikin kafafu, kuma cire sutura a lokacin da ke tattare da jigon daji.

Kamar yadda aka nuna a hoton a kan wannan shafi, mun zaɓa don amfani da hanyar na ƙarshe, ta yin amfani da sutosai 2-inch don haɗa kafafu zuwa plywood.

06 na 10

Ƙaddamar da Jig zuwa Band Saw

Matakan aikin katako na jigon kewaya yanzu sun cika. A cikin wannan mataki, zamu buge jig zuwa ga teburin gadodi don taimakawa wajen kiyaye shi don amfani.

1. Matsayi jig a wuri a kan teburin gangami, sannan kuma ka tabbatar da jig tare da ragowar sararin samaniya don ɗaukar magunguna zuwa ga tebur.

07 na 10

Hašawa Matakan Tsayawa

Tare da takalma biyu a kan babban mahimmanci, hašawa maɗaura daya a kowane gefe kamar yadda aka nuna a wannan hoton. Wadannan karin takunkumi biyu zasu taimaka wajen tabbatar da jigilar shinge lokacin da kake amfani da ita don yanke kayan jari.

08 na 10

Rubuta Lissafin Cibiyar

Tare da jig tabbatacce, matakai na gaba shine marubuci mai layi na tsakiya tsakanin tsawon jig. Za a yi amfani da wannan maƙallan don a ajiye nau'in pivot, inda abin da aka yanke zai juya.

1. A gefen jig wanda ya taɓa murfin band din, auna ma'auni daga gefen jigon zuwa tsakiyar tsakiyar. Alama wannan wuri tare da alamar fensir.
2. Sa'an nan kuma sanya irin wannan alama hudu ƙafa a kan ƙarshen ƙarshen jig ta tebur.
3. Yanzu, tare da rikici, magatakarda wani layin fensir tsakanin waɗannan alamomi guda biyu. Ya kamata a yanzu samun layin da ke fitowa daga ruwa har zuwa ƙarshen jig.

09 na 10

Ana shirya Jig

Lokacin da kake shirye don yin amfani da jigon layinka, kana bukatar ka san radiyar da aka so daga gunkin da ake bukata don aikin aikin katako. Zaka sanya matsayi mai mahimmanci cikin jigonka a nesa wanda ya dace da radius na cikin waya akan aikinka. Za mu yi amfani da ƙusa na 4d a matsayin gwanon pivot.

1. Tare da haɗari, haɗo rami kadan karami fiye da ƙusa 4d a tsakiyar aikin da aka yanke. Da kyau, wannan rami ya kamata a sanya shi a radius nesa daga ɗaya daga gefuna na workpiece. Sai dai idan aikin zai buƙaci rami a cikin wannan wuri, za ku so kawai ku yi rawar rami a wani ɓangare ta wurin aiki, ba tare da nisan mita 1/4 ba.
2. Bayan haka, za ku buƙaci rawar rami irin wannan a cikin jigon cibiyar da kuka rubuta a mataki na karshe. Sanya tsawon radius da ake so daga band saw ruwa kuma sanya alamar fensir a kan layin tsakiya don nuna matsayin fil. Sa'an nan kuma, raɗa wani rami tare da irin bit da kuka yi amfani da samfurin, amma duk hanyar ta cikin jig ta tebur.
3. Da zarar an rami rami, danna 4d gama ƙusa daga ƙarƙashin jig ta cikin rami har kusan kusan 1/4 "a saman tebur.
4. Yi haɗin aiki tare da rami a kan fil kuma a kan gefen band saw band. Matsa kayan aiki a kan fil ɗin har sai ya kwanta a kan tebur.

10 na 10

Amfani da Jig

1. Tare da kayan aiki a wuri a kan shinge mai shinge, daidaita yanayin tsaro a ƙasa har sai dai a sama da aikin da aka yanke. Bayan yin wani gyare-gyare ga ƙungiyar gani, kunna motar kuma jira ruwa don isa cikin sauri.
2. Kusan aiki a cikin ruwa, juya shi a kusa da fil, har sai an yanke dukan siffar sautin. Tabbatar rike da kayan aiki a kan tebur kamar yadda yake juya.
3. Lokacin da aka yanke shi, kashe na'urar da aka gani kafin cire cutoffs. Sa'an nan kuma ya dauke aikin da aka cire daga cikin fil. Idan babu wasu cuts da ake buƙata, cire ƙusa 4d daga jig din kafin ka rarraba naúrar.

Ya kamata a yanzu kuna da wani yanki na yanki na kusa. Sand da raguwa da kuma amfani da aikin aikin katako kamar yadda ake bukata.